Univerzitná knižnica - Vedecké odborné časopisy
Permanent URI for this communityhttps://drepo.uniza.sk/handle/hdluniza/27
Browse
11 results
Search Results
Item Intelligent warehouse systems(University of Žilina, 2024) Biňasová, Vladimíra; Bubeník, Peter; Rakyta, Miroslav; Kasajová, Marta; Zuzik, JánArtificial intelligence can change the overall operation of a business and make work activities more efficient not only in terms of time but also economically. Individual enterprises are increasingly trying to incorporate artificial intelligence into production processes and the need to summarize knowledge about this trend is the main pillar of this paper.Item The perspective of using Industry 4.0 in robotics(University of Žilina, 2024) Biňasová, Vladimíra; Bubeník, Peter; Rakyta, Miroslav; Kasajová, Marta; Zuzik, JánThe contribution focuses on the identification of new possibilities in the robotization of production and assembly processes. In the first section, theoretical knowledge from the given area is presented. The second section presents various trends in the field of artificial intelligence, autonomous technologies and the possibility of their use in the manufacturing industry. New technologies can help businesses with the implementation of individual technologies that can serve to improve production and assembly processes.Item Possibilities of using artificial intelligence in logistics(University of Žilina, 2024) Biňasová, Vladimíra; Bubeník, Peter; Rakyta, Miroslav; Kasajová, Marta; Zuzik, JánThe paper focuses on the topic of the possibilities of using artificial intelligence in logistics. It provides basic information about the given topic, which is presented in the theoretical basis. It describes the definition, history and development and objectives of logistics. It also deals with aspects of Logistics 4.0 and the definition and history of artificial intelligence. The core of the work divides individual options between logistics platforms using artificial intelligence and logistics technologies using artificial intelligence, the principle of operation of which is subsequently described. The conclusion is devoted to the evaluation of the current state of use of artificial intelligence in the logistics industry. It also contains an overview of the advantages and disadvantages of the mentioned possibilities of use.Item Evaluation of the possibilities of use of interactive technology in the laboratory(University of Žilina, 2023) Biňasová, Vladimíra; Bubeník, Peter; Rakyta, Miroslav; Kasajová, Marta; Štaffenová, KatarínaThe goal of the contribution was to propose the possibilities of using interactive technology in the laboratory and to create a creative and interesting environment for students. One of the benefits is facilitating and streamlining the learning process and developing students' creativity. Interactive hardware (interactive whiteboard) and software (multimedia systems) were used to solve the work. The conclusion of the work consists of an evaluation of the benefits of using the interactive whiteboard in the laboratory.Item Evaluation of new trends and reasons for attendance artificial intelligence at the operational level(University of Žilina, 2023) Biňasová, Vladimíra; Bubeník, Peter; Rakyta, Miroslav; Kasajová, Marta; Štaffenová, KatarínaThe contribution is focused on the analysis of the current state of the introduction of artificial intelligence in enterprises in Slovakia. Here are also the results of a questionnaire survey aimed at finding out what the participating small and medium-sized enterprises mean by the term digitization, whether they use it and consider it important. The questionnaire also investigated whether companies are familiar with the national strategies of Industry 4.0 or how they see the service provision and financing system in this context. The conclusion of the article is devoted to the evaluation of new trends and reasons for the emergence of artificial intelligence.Item Industry 4.0 in manufacturing enterprises(Žilinská univerzita v Žiline, 2023) Biňasová, Vladimíra; Bubeník, Peter; Rakyta, Miroslav; Kasajová, Marta; Štaffenová, KatarínaThe paper deals with the analysis the options available to companies for improving the production enterprises as part of the transformation to Industry 4.0. Digital transformation involves the integration of digital technologies and solutions into every area of business. This is a cultural change rather than a technological one, requiring organizations to make fundamental changes in the way they operate and how they deliver experiences and benefits to customers. Digital solutions also help expand the workforce and can lead to the transformation of business processes and business modelsItem Stratégia údržby a efektívny výrobný systém(Žilinská univerzita v Žiline, 2023) Rakyta, Miroslav; Bubeník, PeterIn industrial areas, key maintenance tasks have become an essential part of an organization's overall profitability. Maintenance techniques currently have the ability to significantly increase an organization's competitive advantage in the global marketplace. The first important step is to correctly set up a suitable maintenance strategy. The maintenance strategy of the production support process must, as part of the company's strategy, be based on and support its goals and strategy, perspectives and starting points. Choosing the right maintenance strategy is important for every business. He must determine which strategy will be advantageous for him from the point of view of costs, downtime and other important factorsItem Programmable model of an automated warehouse(Žilinská univerzita v Žiline, 2023) Biňasová, Vladimíra; Bubeník, Peter; Rakyta, Miroslav; Kasajová, Marta; Štaffenová, KatarínaThe paper deals with the multifunctional kit is a robust training model that simulates and demonstrates warehouse automation in the world's most advanced enterprises. Programming takes place in the Siemens TIA Portal software, which is then loaded into a Programmable Logic Automator which is interconnected with the source Siemens SITOP PSU100S. The main objective of the paper was to provide an overview of the current state of-the-art in automated manufacturing and to create an example of an automated warehouse that can be used in teaching as an ideal simulation and demonstration model for training and industrial automation.Item Technológ 3/2022(Žilinská univerzita v Žiline, 2022) Sýkorová, Martina; Bolibruchová, Dana; Bílik, Jozef; Sobota, Róbert; Šuba, Roland; Mojžiš, Milan; Litvaj, Ivan; Dižo, Ján; Blatnický, Miroslav; Ishchuk, Vadym; Molnár, Denis; Štaffenová, Katarína; Rakyta, Miroslav; Bubeník, Peter; Biňasová, Vladimíra; Kasajová, Marta; Tarbajovský, Pavol; Puškár, Michal; Абович Подригало, Михаил; Петрович Кравченко, Александр; Герлици, Юрай; Сергеевич Шеин, Виталий; Сергеевич Ткаченко, Александр; Александровна Кравченко, Екатерина; Kantoríková, Elena; Koňár, Radoslav; Matejka, Marek; Podprocká, Radka; Kostrzewski, Mariusz; Jerzy Nowak, Wojciech; Medňanský, Martin; Brůna, MarekVplyv teploty precipitačného vytvrdzovania na vlastnosti zliatiny AlSi5Cu2Mg legovanej Zr || Seamless Tubes Manufacturing Processes Analysis || Decision-making process and knowledge management, knowledge management and skills || Nákladné prívesy za traktor - koncepčné usporiadanie a ich typy || Proces reverzného inžinierstva s využitím 3D laserového skenovania || Nákladné prívesy za traktor - špeciálne verzie a zvláštna výbava || Knowledge, knowledge management and innovations || Návrh modelu parného rušňa || Integrovaný systém pre redukciu emisií spaľovacích motorov || Technical preparation of production || О выборе мощности двигателя автомобиля на этапе проектирования || Vplyv tepelného spracovania na nástrojové ocele || Skúsenosti pri ultrazvukovom skúšaní zvarov v praxi || Hodnotenie tepelného zaťaženia vysokotlakovej formy pomocou numerickej simulácie || Rzeczy kilka o transporcie kolejowym ładunków w Japonii || Precipitačné vytvrdzovanie Al-Si-Cu-Mg zliatin || Numerické simulácie vplyvu technologických faktorov na štruktúru vysokotlakových odliatkovItem Technológ 2/2022(Žilinská univerzita v Žiline, 2022) Mičietová, Anna; Minárik, Peter; Čilliková, Mária; Neslušan, Miroslav; Čapek, Jiří; Sivák, Samuel; Maláková, Silvia; Harachová, Daniela; Kulya, Juliy Martyn; Tomáš, Miroslav; Evin, Emil; Kantoríková, Elena; Moravec, Ján; Galčík, Marek; Brůna, Marek; Širanec, Lukáš; Bolibruchová, Dana; Bronček, Jozef; Drbúl, Mário; Konstantová, Viera; Kožienka, Lukáš; Koňár, Radoslav; Šutka, Jozef; Blatnický, Miroslav; Dižo, Ján; Molnár, Denis; Bubeník, Peter; Kolesnyk, Olha; Rakyta, Miroslav; Čapek, Juraj; Frátrik, Martin; Mičian, Miloš; Trško, Libor; Hirjak, Rastislav; Mišaneková, Viera; Chudíková, Dáša; Šimko, Radomír; Piroško, Martin; Jaremko, Matúš; Uhrík, Radoslav; Melo, Borislav; Málek, Miroslav; Mičian, Miloš; Derďák, Ján; Sikora, Eduard; Baba, Marcel; Kotora, Miroslav; Kamenský, Rastislav; Pobočíková, Ivana; Guldan, Vladimír; Sedliačková, Zuzana; Chupáč, Radoslav; Кравченко, Александр Петрович; Кравченко, Екатерина Александровна; Дижо, Ян Янович; Блатницкий, Мирослав ЯновичAbstract: This paper deals with surface integrity after shot peening of AlSi 304 under variable conditions expressed in term of shot-peening cycles and corresponding Almen intensities. Surface state is investigated from the point of view of surface topography, surface roughness and microhardness. Also phase transformation of paramagnetic austenite into strain induced martensite is investigated as well by the use of Barkhausen noise technique. It was found that the fraction of strain induced martensite grows with the number of shot-peening cycles and its extent penetrates deeper beneath the free surface. Furthermore, surface roughness decreases along with increasing number of cycles. Surface microcracking occurs after prolonged shot-peening cycles. Abstract: Paper was devoted to new methods coming to wide use in design engineering. These methods contained of topology optimization and generative design. Although topology optimization is practiced for some time, the generative design is its biggest contender. Both methods were described in a way of how they work and what methodology needs to be abided. At the end, a comparison between advantages and disadvantages as well was done, taking into account use of both of them in gear wheel body optimization. Abstract: The paper focuses on the manufacturability optimization of the of case made of aluminium by the rubber forming process. Al6016 aluminium was considered as the material for the cover and its constitutive equations were defined by Hill 48 and Hollomon models. The Mooney-Rivlin hyperelastic material model described the material properties of the rubber-made punch. Simulation model was built in Pam stamp software and the results were evaluated as well. The results were optimized in terms of thickness thinning and punch stroke, for two different rubber hardness. Abstract: The article describes the method of boriding sintered carbides type H1 (K10) and G1 (K20) and tool steel Cr-Mo-V. The aim of this work is to analyze the knowledge about boriding of steels with the focus on the technological assumptions of the use of boriding in the production process of forming tools in order to increase the resistance to friction, abrasive and adhesive wear. Interestingly, boriding is still an unconventional method of surface treatment. The presented work deals with the structural analysis of borided layers. Steel samples of 1.2365 material and sintered carbides H1 (K10), G1 (K20) borided with EKabor 2 powder were monitored. For the testing of metallographic samples, the methodology developed for the study of the microstructure of sintered carbides was developed. The monitored samples, borided at 900 °C for 240 min, obtained a uniform layer 5 μm thick. An increase in microhardness of more than 700 HVM was measured for carbide H1 (K10) and almost 1500 HVM for G1 (K20). The increase in hardness is due to the formation of dispersed cobalt borides Co2B and CoB. Abstract: Submitted paper aims to further analyse the possibilities of melt velocity reduction in the gating system. In this work was designed the naturally pressurized gating system. Proposed design appears to be a suitable solution for reoxidation processes reduction. Disadvantage of this system is that the melt velocity is supercritical, which leads to splashes of the melt when entering gates. Main focus of experimental part is to find a proper way to reduce the melt velocity, which will consequently decrease the reoxidation processes. For the purpose of the melt velocity reduction, labyrinth filters, flat filters and foam filters effect were investigated and visualized by simulation software ProCAST. Experimental casts were carried out, to be able to verify the results of the simulations. Mechanical properties and porosity evaluation was investigated on casted samples. Flat and foam filter appeared to be a suitable to melt velocity reduction and it was associated with increasing mechanical properties of castings. Construction with foam filter achieved the best results. Abstract: The aim of this paper was to analyze the impact of different zirconium addition (0.05; 0.10; 0.15 and 0.20 wt. % Zr) on selected properties of AlSi5Cu2Mg aluminum alloy. It is a new alloy for cylinder head castings and has only been used for a relatively short time. The specificity of this alloy is its chemical composition - specifically the low permitted Ti content, which makes it impossible to refine the grain structure of this alloy using standard Al-Ti-B grain refiners. The results of our research showed that increasing zirconium content had no effect on the increase in ultimate tensile strength, yield strength and hardness of as-cast samples. After T7 heat treatment, a more significant increase in UTS, YS and thermal conductivity occurred due to the precipitation of Cu- and Mg rich strengthening precipitates. Zirconium-rich intermetallic phases were observed in the shape of separate thick needles or as a cluster of two crossed thinner needles. These phases were not affected even after heat treatment, indicating their high thermal stability. Increasing the Zr content was accompanied by an increase in liquidus temperature and area fraction of porosity values. Abstract: International Standard EN ISO 22081 sets out rules for the definition and interpretation of general geometric specifications and general dimensional specifications according to Article 5.12 of ISO 8015: 2011). The general GPS specifications apply individually to each characteristic of a geometric element or to a relationship between geometric elements for which no individual GPS specification of the same type is defined. The general GPS specifications, which prescribe general dimensional and geometric tolerances, make it possible to simplify the indications and thus the reading of the drawing documentation, while at the same time facilitating the selection of tolerances. The new standard EN ISO 22081 replaces the standard ISO 2768 and gives rules for the application of the general geometric and general dimensional specification. Abstract: The paper deals with the limitations of testing ferromagnetic materials by the magnetic particle method. It focuses mainly on the influence of orientation and depth of materiál defects on the reliability of identification of surface and volume defects when using color and UV methods. The results obtained using unidirectional and alternating pole magnetization in manual control with a magnetic yoke are compared. Abstract: The article deals with the historical development and analysis of the current state of handling machines used in the entertainment industry. It points in particular to the material aspect, i.e. materials used for the production of amusement park equipment components. The article represents an important aspect that precedes the design of such a device, respecting the currently valid legislative requirements based on the standard STN EN 13814 so as to ensure protection against injuries or potentially dangerous situations (ejection, falling out, hitting, etc.). Abstract: The growing trend of using and processing big data brings space to study, analyze and understand the performance aspects of the monitored advanced technologies. In general, benchmarking is a well-known tool in the world of software systems that is commonly used to identify companies' strengths and weaknesses. The article presents the use of the benchmarking tool as a tool for evaluating the application of advanced technologies supporting the management of the production process. Abstract: The strength of fine-grained HSLA steels is mainly based on the grain boundary strengthening, which as the only strengthening mechanism allows the yield strength to increase without a decrease in ductility. Therefore, any change in grain size leads to irreversible changes in the properties of the material. Such changes also occur in the coarse-grain heat affected zone (CGHAZ) of welded joints, where there is an increase in austenitic grain size, which leads to a decrease in yield strength, or decrease of fatigue strength. The paper experimentally determines the growth kinetics of austenitic grain for S960MC steel. Based on the measured data, it will be possible to predict the grain growth kinetics in the CGHAZ and FGHAZ. The acquired knowledge will help to set the welding processes of fine-grained steels. The measured data will also provide a basis for numerical simulations of metallurgical processes in high-temperature HAZ during welding. Abstract: One of the basic requirements of the current industrial production is to extend the life time of thermal aggregates while taking into consideration the maximum economic effectiveness. The use of non-shaped refractory mixtures for manufacturing of monolithic linings represents a progressive trend that replaces traditional brick linings. Non-shaped materials enable to create linings of different shapes and sizes, their firing takes place at the consumer and their repair is much simpler. These aspects increase the productivity and save energy. The paper covers practical applications of castables from the production of the company RMS Košice s.r.o. in the foundry industry. Abstract: The article is a continuation of research dealing with the construction of entertainment facilities. The main goal of the authors is therefore to design such an entertainment device according to their own design. This goal was preceded by a historical overview of the development of transport and handling technology used in the entertainment industry. The current work aims to analyse the main components used in the construction of these devices such as nacelles, seats, restraints or drives and fasteners according to STN EN 13814 so that the design meets all requirements. Abstract: The paper is supplemented by a discussion of the results and in the end an evaluation of the experiments is made. The paper presents basic theoretical knowledge about the cutting process. The experimental part describes the cutting, forming and evaluation of the obtained cylindrical samples for rolling elements. Abstract: Residual stress plays an important role in welded structures, which are stressed not only by cyclic loading. The work deals with the creation of a butt weld joint made of HSLA steel S960MC with a thickness of 3 mm and its subsequent analysis for residual stresses. The result of the work is the evaluation of the residual stresses of the welded joint. Abstract: In addition to the mechanical properties, the formability and appearance after painting of the coated sheets depends on the surface texture. The surface roughness characteristics of the sheet, the mean arithmetic deviation Ra and the number of peaks per centimetre Pc, depend on the surface texture of the finishing rolls of the rolling mill, their wear and the removal on the rolling mill. This paper presents the results of an investigation of surface-finished sheet metal, the surface of which was textured by changing the electrodischarge texturing (EDT) parameters of the finishing rolls of a rolling mill. The optimization of current Ip, voltage Up, pulse duration POnT and pulse off time POffT on the target values of roughness RaT,FR and number of peaks PcT,FR of finishing rolls was carried out by response surface methodology (RSM). The obtained regression models describe with a high degree of accuracy the relationships between the input electrodischarge texturing parameters of the finishing rolls and the output texture characteristics RaT,FR and PcT,F Abstract: The issue of the conditions and suitability of the supply of glass to the dispenser head can be precisely solved only with the use of knowledge of fluid mechanics. The paper presents the used calculation methods of finite parameters and also makes their mutual comparison in terms of suitability of the solution. Abstract: In the hot metal and steel production the thermal equipment used for their production is essential with respect to the associated costs. The lining of torpedoes, blast oxygen furnaces, hot metal and steel ladles must withstand challenging manufacturing conditions. The working lining, that gets in contact with hot metal, wears out since it is affected by molten metal. The permanent lining on the other hand fulfills the safety and insulation function. The permanent lining is supposed to collect molten metal if the working lining is worn out and keep the metal temperature on the level of processing. When emptying a ladle, the lining protective layer (scab) is created if the temperature on the working lining surface is lower than the metal melting temperature. When designing the lining composition, the emphasis is given to material properties, as well as to its life time at the lowest costs per ton of steel. The paper evaluates permanent linings of metallurgical aggregates based on their thermal shock resistance and level of penetration into the brick volume. Abstract: The paper deals with an overview of selected additive technologies used in the automotive industry. The emphasis is mainly on technologies that use metal powders. Furthermore, the work focuses on machine improvements and also presents a possible breakthrough in series additive production thanks to new production systems. Abstract: The paper presents the application of one-way analysis of variance (ANOVA) and Tukey's HSD method of multiple comparison, which can be used in the experiment, which determined the effect of cutting speed on the perpendicularity deviation of the cutting surface when cutting stainless steel X5 Cr Ni 1810 using laser. The details and technological parameters of laser cutting steel are mentioned. Based on the results obtained using ANOVA and Tukey's HSD method, it can be argued that different cutting speeds have a statistically significant effect on the perpendicularity deviation of the cutting surface. Abstract: The solution of electromagnetic compatibility and resistance of equipment to atmospheric discharges is a very important issue in the development and testing of electrotechnical and electronic equipment. The paper presents a numerical calculation of the parameters of a simplified mathematical model of a trial current and voltage pulse, which is defined by the IEC 61000-4-5 standard. The simplification consists in replacing the current pulse leading time, which is determined by said standard as 1.25 times the time from reaching 10% of the maximum amplitude to reaching 90% of the maximum amplitude, by a time from 0% to 100% of the maximum amplitude. For the solution of the equations for the calculation of the parameters of the simplified model by the numerical Newton - Raphson method, the initial approximation of the solution is determined and the cases when the solution does not exist are determined. Abstract: The paper discusses that the filtration of castings influences the deformed resistance. The article describes the change in toughness in castings using filtration during casting and subsequent changes in mechanical properties after forming these castings. Subsequently, the volumetric compressibility of samples of the same material was monitored. The chosen material is aluminium alloy due to good formability. The mechanical properties after forming on the filtered casting were compared with the casting without filtration. The essence of the tests is to ensure the behaviour of the material in two mutually different environments and to compare the size of the barrel and the susceptibility to cracking on the circumference of the samples. The experiment confirmed the effectiveness of filtering and its effect on the forming force. Abstract: The results of a survey of the reliability of automobile trains in the composition of MERCEDES-BENZ 1844 ACTROS LS trucks and semi-trailers KÖGEL, KRONE, SCHMITZ at different stages of operation are presented. The malfunctions of units and assemblies are revealed, regularities are established, the causes of malfunctions and failures are determined.